three factors that cause the terminals of connector to be bad

-
The terminal is a metal piece disposed inside the insulating material of the connector, and its function is to guide the electrical connection between the wire and the electronic device. As the precision of the industrial automation control is more and more strict, the amount of the terminal is always increased, but some bad factors will happen in the process when the terminal is in use.so yeahui introduces three factors that cause the terminals of connector to be bad.

Three factors that cause the connector terminals to be bad

the poor insulation of connector terminals
The function of the connector terminal insulator is to keep the contacts in the correct position and to insulate the contacts from the contacts and the contacts from the housing. Therefore, the insulation must have excellent electrical properties, mechanical properties and process forming properties. In particular, with the high density and wide use of miniaturized terminals, the effective wall thickness of the insulator is getting thinner and thinner. This puts more stringent requirements on insulation materials, injection mold precision and molding processes.
Connector terminals are not fully fixed
The connector terminals need to be fixed at a specific position to achieve a stable connection. If the installation is not perfect or the product insertion and extraction life cycle is insufficient caused the fixing is poor, and the Lighter influences contact and causes instantaneous power failure, and the serious  will disintegrate the product. Disintegration refers to the abnormal separation between the plug and the socket between the plug and the socket caused by the unreliable structure due to the material, design, process, etc., which will cause the power transmission and signal of the control system  to be interrupted. Due to unreliable design, incorrect material selection, improper selection of molding process, poor quality of heat treatment, mold, assembly, welding, etc., assembly failure, etc. will result in poor fixation.
the poor contact of the connector terminals
The metal conductor inside the connector terminal is the core part of the terminal, which transmits power, signal, etc. to other parts in contact with it, so the metal conductor inside the terminal must have good conduction properties. If the contact design is unreasonable, the material selection is wrong, the size is not standard, or the plating layer is improperly handled, the contact of the connector terminals may be poor.
Yahui Electronics Co., Ltd. has been manufacturing connectors for more than 10 years, and we have a professional team to support us. In the process of producing connectors, we are very strict in the detection of quality, and we need to pass multiple tests and screening for each material used. If you want to buy some good quality obd connector, you can come to us to contact us and look forward to your message.

评论

发表评论

此博客中的热门博文

What is the Difference Between J1939 Connector Type 1 and 2?

-
图片
  SAE J1939 (hereinafter referred to as J1939) is the recommended standard of the American Society of Automotive Engineers (SAE). It is controlled and communicated by the "Truck and Bus Electrical & Electronics Committee" (Track & Bus Electrical & Electronics Committee). Developed and written by the Track & Bus Control and Communications Network Subcommittee. J1939 has become a recognized industry standard and choice for commercial vehicle diagnostics and data communication heavy, off-highway, truck, bus, ship propulsion, power generation, industrial pumping, construction, and material handling machinery. J1939 is a high-level protocol network (CAN) based on Controller Area. It is widely used by the diesel engine industry to provide diagnostic data such as vehicle engine speed, temperature, oil temperature, exhaust emissions, and other customizable options. J1939 connectors are divided into black and green rubber cores, but do you know the difference between t...
阅读全文

Benefits of overmolded connectors and wiring harnesses?

-
图片
What is overmolding? In short, overmolding is an injection molding process in which two or more materials are used to combine a harness wire and a connector to form a single part, and the cable assembly is placed in a mold. In this process, the first material substrate will be covered by other materials. The overmolding process requires the use of insert molding (single injection) or multiple injection molding techniques to cover rigid plastic parts with TPU layers or other overmolding materials. So what are the benefits of the connector and harness overmolding process? Benefits of overmolding connectors and harnesses: 1. Increase the flexibility of the cable harness exit so that most of the movement between the cable harness and the connector occurs at the cable harness exit. 2. Provide abrasion resistance, impact resistance or impact resistance. 3. Fix the cable assembly by sealing the assembly in plastic. 4. Provide 360 degree strain relief and increase tension. 5. Cr...
阅读全文

​Cars are equipped with diagnostics tool or obd-ii ports

-
图片
Modern cars have the capacity of a few computers, are tooled with software that contains millions of lines of programming code and produce gigabytes of data, but they are still different from connected cars. ​ A smart vehicle is able to optimize its performance to reduce fuel consumption, show the best path to follow taking into account current traffic and weather conditions, detect errors in the engine and collect information data to negotiate lower insurance rates. Most cars and light trucks are equipped with on-board diagnostics or an OBD II port that provides access to data from the engine control unit (ECU). To get the information you need to plug in an external device. The OBD-II specifications provide a standardized hardware interface - a female 16-pin (2x8) J1962 connector, so a single external device can be used for most car models. It also should have an Internet connection to transfer the collected data. OBD-II connects to the Internet, and generally needs to use th...
阅读全文