What is the IPC620 Standard

-
The IPC standard is the most important standard document for electronic engineering personnel. It has very authoritative and enforceable regulations on the reliability, safety, standardization, and manufacturability of electronic equipment and systems.
What is the IPC620 Standard​
This standard is an appearance acceptance standard related to cable assembly established by the Cable Assembly Association and the Electronic Connection Products Committee. If no standards for process inspection and finished product inspection are defined, IPC 620 can be used as the inspection standard document for the product alone. It establishes process control or defective products that allow repair/rework. This information suggests that it needs to be improved through statistical process control plans.
IPC 620 mainly includes the following: conductor/cable preparation, measurement of cable assemblies and conductors, crimp terminals, insulation piercing connections, solder terminals, connector connections, compression/injection molding, articulation, marking/labeling, Fastening, wire harness/cable electrical shielding, wire harness/cable protection layer, coaxial and biaxial cable assembly, no soldering.
The customer has the ultimate responsibility to identify which level is acceptable. Therefore, the decision to accept or reject must be based on relevant standards, such as contracts, drawings, specifications, standards, and reference documents. There are three product levels in this standard. as follows:
Level 1-General electronic products: The main function of the product after assembly is application.
Level 2-Dedicated electronic products: The product requires that it can continue to be used beyond its life cycle and can operate without accidents. The characteristic is that the environment of the end-user will not cause damage to the product.
Level 3-High-tech electronic products: the use of the product is extremely strict, no equipment is allowed to be shut down, the environment of the end-user is extremely unusual, and the function of the equipment must also meet the requirements, such as its life cycle requirements and other Special requirements.
If the standards conflict, the following sequence must be followed:
1. Unify the standards of customers and suppliers.
2. Sample drawings and assembly drawings should reflect the detailed requirements of customers.
3. Provide IPC 620 to the customer or be reflected in the contract.

Yeahui is a connector supplier with 11 years of experience in developing high-quality connectors and wiring harnesses. We have many types of products, including obd connector, circular connector, agricultural connector, and so on. We can meet the requirements of various customers. Feel free to learn more about connectors or buy our connectors, looking forward to your message.

评论

发表评论

此博客中的热门博文

What is the Difference Between J1939 Connector Type 1 and 2?

-
图片
  SAE J1939 (hereinafter referred to as J1939) is the recommended standard of the American Society of Automotive Engineers (SAE). It is controlled and communicated by the "Truck and Bus Electrical & Electronics Committee" (Track & Bus Electrical & Electronics Committee). Developed and written by the Track & Bus Control and Communications Network Subcommittee. J1939 has become a recognized industry standard and choice for commercial vehicle diagnostics and data communication heavy, off-highway, truck, bus, ship propulsion, power generation, industrial pumping, construction, and material handling machinery. J1939 is a high-level protocol network (CAN) based on Controller Area. It is widely used by the diesel engine industry to provide diagnostic data such as vehicle engine speed, temperature, oil temperature, exhaust emissions, and other customizable options. J1939 connectors are divided into black and green rubber cores, but do you know the difference between t...
阅读全文

Benefits of overmolded connectors and wiring harnesses?

-
图片
What is overmolding? In short, overmolding is an injection molding process in which two or more materials are used to combine a harness wire and a connector to form a single part, and the cable assembly is placed in a mold. In this process, the first material substrate will be covered by other materials. The overmolding process requires the use of insert molding (single injection) or multiple injection molding techniques to cover rigid plastic parts with TPU layers or other overmolding materials. So what are the benefits of the connector and harness overmolding process? Benefits of overmolding connectors and harnesses: 1. Increase the flexibility of the cable harness exit so that most of the movement between the cable harness and the connector occurs at the cable harness exit. 2. Provide abrasion resistance, impact resistance or impact resistance. 3. Fix the cable assembly by sealing the assembly in plastic. 4. Provide 360 degree strain relief and increase tension. 5. Cr...
阅读全文

​Cars are equipped with diagnostics tool or obd-ii ports

-
图片
Modern cars have the capacity of a few computers, are tooled with software that contains millions of lines of programming code and produce gigabytes of data, but they are still different from connected cars. ​ A smart vehicle is able to optimize its performance to reduce fuel consumption, show the best path to follow taking into account current traffic and weather conditions, detect errors in the engine and collect information data to negotiate lower insurance rates. Most cars and light trucks are equipped with on-board diagnostics or an OBD II port that provides access to data from the engine control unit (ECU). To get the information you need to plug in an external device. The OBD-II specifications provide a standardized hardware interface - a female 16-pin (2x8) J1962 connector, so a single external device can be used for most car models. It also should have an Internet connection to transfer the collected data. OBD-II connects to the Internet, and generally needs to use th...
阅读全文