The Injection molding temperature of pin connector is too high

-
In the process of injection molding, the temperature of the pin connector is a very critical factor, and its level will directly affect the quality of the injection molding process.What happens if the Injection molding temperature of  pin connector is too high?The introduction of yeahui is as follows.
The Injection molding temperature of pin connector is too high
First, Thermal deformation of the machine:
The moving parts with different thermal expansion coefficients in the hydraulic components are stuck due to the smaller matching clearance, causing malfunction. It will affect the transmission precision of the hydraulic system, and also affect the working quality of the components.
Second, reduce the viscosity of the oil:
Excessive temperature rise in the injection molding machine will result in lower viscosity of the oil, increased leakage, the volumetric efficiency of the pump and the efficiency of the entire system are significantly reduced. As the viscosity of the oil is lowered, the oil film of the moving parts such as the slide valve is thinned and cut, and the frictional resistance is increased, It will result in an increased wear.
Third, Deform the rubber seal:
In the actual test, it was found that the excessive temperature rise of the injection molding machine would deform the rubber seal, accelerate the aging failure, reduce the sealing performance and service life, and cause leakage.
Fourth, the oxidation and deterioration of the oil:
If the temperature rise of the injection molding machine is too high, it will accelerate the oxidation and deterioration of the oil, precipitate the asphalt material, and reduce the service life of the hydraulic oil. The precipitate blocks the damper orifice and the slit valve port, causing the pressure valve to become stuck and unable to move, the metal pipe to be elongated and bent, or even broken.
The above article is the impact of the connector injection temperature is too high.Do you want to know more about connectors? please read Connectors are widely used.

评论

发表评论

此博客中的热门博文

What is the Difference Between J1939 Connector Type 1 and 2?

-
图片
  SAE J1939 (hereinafter referred to as J1939) is the recommended standard of the American Society of Automotive Engineers (SAE). It is controlled and communicated by the "Truck and Bus Electrical & Electronics Committee" (Track & Bus Electrical & Electronics Committee). Developed and written by the Track & Bus Control and Communications Network Subcommittee. J1939 has become a recognized industry standard and choice for commercial vehicle diagnostics and data communication heavy, off-highway, truck, bus, ship propulsion, power generation, industrial pumping, construction, and material handling machinery. J1939 is a high-level protocol network (CAN) based on Controller Area. It is widely used by the diesel engine industry to provide diagnostic data such as vehicle engine speed, temperature, oil temperature, exhaust emissions, and other customizable options. J1939 connectors are divided into black and green rubber cores, but do you know the difference between t...
阅读全文

Benefits of overmolded connectors and wiring harnesses?

-
图片
What is overmolding? In short, overmolding is an injection molding process in which two or more materials are used to combine a harness wire and a connector to form a single part, and the cable assembly is placed in a mold. In this process, the first material substrate will be covered by other materials. The overmolding process requires the use of insert molding (single injection) or multiple injection molding techniques to cover rigid plastic parts with TPU layers or other overmolding materials. So what are the benefits of the connector and harness overmolding process? Benefits of overmolding connectors and harnesses: 1. Increase the flexibility of the cable harness exit so that most of the movement between the cable harness and the connector occurs at the cable harness exit. 2. Provide abrasion resistance, impact resistance or impact resistance. 3. Fix the cable assembly by sealing the assembly in plastic. 4. Provide 360 degree strain relief and increase tension. 5. Cr...
阅读全文

​Cars are equipped with diagnostics tool or obd-ii ports

-
图片
Modern cars have the capacity of a few computers, are tooled with software that contains millions of lines of programming code and produce gigabytes of data, but they are still different from connected cars. ​ A smart vehicle is able to optimize its performance to reduce fuel consumption, show the best path to follow taking into account current traffic and weather conditions, detect errors in the engine and collect information data to negotiate lower insurance rates. Most cars and light trucks are equipped with on-board diagnostics or an OBD II port that provides access to data from the engine control unit (ECU). To get the information you need to plug in an external device. The OBD-II specifications provide a standardized hardware interface - a female 16-pin (2x8) J1962 connector, so a single external device can be used for most car models. It also should have an Internet connection to transfer the collected data. OBD-II connects to the Internet, and generally needs to use th...
阅读全文